DEI 700T Installation Guide

®© 2001 Directed Electronics, Inc. Vista, CA N700T 8-01Rev. E 1.1Model 700TInstallation Guide®Downloaded from: http://www.guardianalarms.net

10 © 2001 Directed Electronics, Inc. Vista, CA4. Turn the ignition key switch to the start position. Make sure the car is not in gear! If your meter r

© 2001 Directed Electronics, Inc. Vista, CA 113. Insert the twisted pair of wires into one end of the butt connector and crimp securely.4. Insert the

12 © 2001 Directed Electronics, Inc. Vista, CAprimary harness (H1) wire connection guideThis guide describes in detail the connection of each wire. Al

© 2001 Directed Electronics, Inc. Vista, CA 13As shipped, this wire should be connected to the (+) parking light wire. If the light flash polarity jum

14 © 2001 Directed Electronics, Inc. Vista, CAConnect this wire to the optional domelight supervision relay.IMPORTANT! This output is only intended to

© 2001 Directed Electronics, Inc. Vista, CA 15This wire is used in vehicles that have a positive (+) switched dome light circuit. Connect the violet w

16 © 2001 Directed Electronics, Inc. Vista, CAConnect this to the red wire of the siren. Connect the black wire of the siren to (-) chassis ground, pr

© 2001 Directed Electronics, Inc. Vista, CA 17auxiliary harness (H2) wire connection guideThis wire supplies a (-) 200 mA output that can be used to h

18 © 2001 Directed Electronics, Inc. Vista, CAhas no function. If the customer wants the system to automatically lock the doors when the system passiv

© 2001 Directed Electronics, Inc. Vista, CA 19This system is used in many four-door GM sedans. To test for this type of system, probe the unlock wire

2 © 2001 Directed Electronics, Inc. Vista, CAtable of contentsWhat Is Included . . . . . . . . . . . . . . . . . . . . . . 3Installation Points to Rem

20 © 2001 Directed Electronics, Inc. Vista, CANOTE: Failure to insert the diodes at the correct point will allow the system to be disarmed by oneof th

© 2001 Directed Electronics, Inc. Vista, CA 213. Press and HOLD the Valet/program for three seconds. 4. The LED will flash once to confirm the lock po

22 © 2001 Directed Electronics, Inc. Vista, CAinternal programming jumperThis jumper is used to determine the light flash output. In the (+) position,

© 2001 Directed Electronics, Inc. Vista, CA 23system features learn routineThe System Features Learn Routine dictates how the unit operates. It is pos

24 © 2001 Directed Electronics, Inc. Vista, CA2. Then press the Valet/program switch once more and HOLD it. For example, if you just programmed the se

© 2001 Directed Electronics, Inc. Vista, CA 253 SIREN DURATION 30/60 SECONDS: In the default setting, the full triggered sequence will continue when t

26 © 2001 Directed Electronics, Inc. Vista, CAtable of zonesWhen using the diagnostic functions, use the Table of Zones to determine which input has t

© 2001 Directed Electronics, Inc. Vista, CA 27 Door input does not immediately trigger full alarm. Instead, first I hear chirps for three seconds. Th

28 © 2001 Directed Electronics, Inc. Vista, CAwiring quick reference guide

© 2001 Directed Electronics, Inc. Vista, CA 3what is included One control module with on-board shock sensor One plug-in status LED One plug-in Vale

4 © 2001 Directed Electronics, Inc. Vista, CAtools requiredThis is a general list of tools required to complete the installation of this security syst

© 2001 Directed Electronics, Inc. Vista, CA 5 Never put the control module in the engine compartment! The first step in hot-wiring a vehicle is remo

6 © 2001 Directed Electronics, Inc. Vista, CAIMPORTANT! When the vehicle is delivered, please show the user where the switch is located andhow to disa

© 2001 Directed Electronics, Inc. Vista, CA 7wiring! Exposed yellow butt connectors do not look like factory parts, and will not fool anyone! For this

8 © 2001 Directed Electronics, Inc. Vista, CAHow to find (+)12V ignition with your multimeter:1. Set to DCV or DC voltage (12V or 20V is fine).2. Atta

© 2001 Directed Electronics, Inc. Vista, CA 9The best places to find the door pinswitch wire are: At the pinswitch: When testing at the pinswitch, ch